How does an eyelet setter work

Grommets are very similar to eyelets , because they are used to reinforce a hole as well; however, grommets are typically used for more heavy duty material than eyelets.

Additionally, how do you punch eyelets? Published on Jan 6, Punch a hole slightly smaller than the shaft of the eyelet into the leather. Insert the eyelet with rim on the good front side of the leather. Use an eyelet setting tool. Insert tool into the center of eyelet and hammer gently. Eyelet pliers are a tool that crimps eyelets through a hole in a piece of fabric or another material to prevent rips and frays. If you want to add an eyelet to something, simply make a hole in the material so you can position an eyelet inside of it.

Once the eyelet is in place, squeeze it in the pliers to secure it. Pin the eyelet tape along the top edge of the fabric and sew into place. Draw around the inside of each ring with a fabric pen, then cut out these circles to create the eyelet holes. About the Author: Mark the spots where you want to punch holes in your fabric with fabric chalk. Rotate the wheel on a rotary leather punch until the punch size that you want is lined up with the other side of the punch.

Position the punch over the mark on the fabric with the flat end of the punch under the fabric. Flexzion Grommet Machine Kit. Yaheetech Manual Grommet Banner Press. Tenive Heavy Duty Eyelet Maker. Yescom Grommet Machine. Clevr Hand Press Grommet Machine.

An eyelet is a hole that is punched into the shoe's upper that allows shoelaces to be threaded through. Eyelets are commonly reinforced with a metal or plastic grommet that covers the holes and prevents fraying. Whether or not they are reinforced with a plastic or metal grommet depends on the style of the shoe. You will need a hole punch, the eyelet tool or tapered punch large enough to spread the eyelet and an anvil of some sort with a hole.

You can use scissors if you have no other hole punch, I usually cut an x on the center of my hole then remove the excess material if I do it this way. Now that your hole is punched, put the male end of the eyelet through the hole. You want the male end on the side that will be most visible as this side is the better looking.

Once the male end is through the hole, place the female end, or washer over the post. With the two ends of the eyelet assembled around your material, you can commence to setting the eyelet. Using your eyelet tool or tapered punch and your anvil, place the eyelet in the anvil with the post facing up and the female end washer towards you. Place the tapered end of the eyelet tool into the post and hammer. I find that two or three solid hits from a metal hammer, or a few extra from a wooden mallet usually do the trick.

Check to make sure that all the excess material has been spread and the eyelet is snug, and you are good to go. Important: especially with smaller eyelets, place a piece of fabric between the anvil and the male part of the eyelet. Otherwise, the eyelet has a good chance of getting stuck, the only solution being to destroy the eyelet.

If you have decided against investing in a hole punch, then scissors will be essential. This pair is great for the price.

Or if you want to invest a bit more into scissors that give you more precision on small cutting work, this pair is fab! I have ordered from different suppliers, but find it easier and faster to order a variety from Amazon. This colourful pack of eyelets would add an interesting flourish to your makes.

These solid brass ones come in either a kit or as a refill. You can then buy more grommets as needed. I have multiple die pieces for this purpose! If you are adding eyelets or grommets to your garment, you will need to reinforce the fabric. You can do this with fusible interfacing, or and additional piece of fabric. For both techniques, cut a small square and place where your eyelet will be inserted. For this example, I have simply grabbed a small section. Before you can put eyelets in fabric, you need to carefully mark where you want the eyelet to go.

I do this with a pen, marking a cross for accuracy. You could also simply mark it with a dot. Now that you have the spot marked, you need to create a hole for the shaft of the eyelet to pass through.

There are several ways to do this. If you are using scissors to create the hole, I like to make a small x, with precision scissors. This allows us to manoeuvre the eyelet shaft in carefully, without stretching the fabric too much. This photo shows the six different sized holes I am able to have with my hole punch. For anyone that prefers the circular hole vs a cut x, but does not want to invest in the hole punch, this technique is for you. You can see that this leather is quite thick, and the hole punch bit did not pierce all the way through.

When using eyelet pliers, you first need to buy some pliers grab the Prym pliers here! Step 4: Insert the Eyelet into the hole. Make sure that the shaft is extending from the right side to the wrong side!!! Step 6: Squeeze the pliers closed so that the metal part of the bit comes down and connects with the eyelet shaft.

Step 2: Insert the shank of your eyelet into the hole in the fabric, with the fabric facing right side down. Step 3: I have chosen to reinforce the fabric with a second piece of fabric, so I lay this over the eyelet too. Step 4: Lay the washer part of the eyelet on top of the fabric layers, making sure it is placed the right way.

Step 5: Load the bits die onto the piston pliers. Be sure to insert the correct piece into the correct section! Step 7: Slowly squeeze the pliers together, exerting enough pressure to squish the two die pieces together and crush the shaft of the eyelet over the washer part. The third way to put an eyelet in fabric us using your hammer.

Now, you will want a rather sturdy hammer for this, in order to apply enough oomph to crush the shaft of the eyelet around the fabric hole.